Buy Analogue input module,IE8 mA IE8. Browse our Mfr. Part No. IE8; Brand Allen Bradley I/O,module,Flex User Manual. Legislation. (Cat. No. IE8 Series B). 4. 1. 3. 2. 5. 6. 7. Module Installation. This module mounts on a terminal base unit. 1. the module. Installation Instructions. User manual • Read online or download PDF • Rockwell Automation IE4XOE2,IE8,OE4,D FLEX I/O ANALOG MODULE User.

Author: Melrajas Basida
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Health and Food
Published (Last): 13 April 2009
Pages: 386
PDF File Size: 19.69 Mb
ePub File Size: 3.45 Mb
ISBN: 242-7-94537-251-1
Downloads: 10096
Price: Free* [*Free Regsitration Required]
Uploader: Vull

Calculate the power requirements of all modules in each chassis. This bit is set to 1 when all bits in the configuration register write word 3 are 0 unconfigured state. Then it initiates a block transfer write to configure the module if the power up bit is set.

Position the terminal base on the 35 x 7. Off position now produces 0V or 0mA, dependent upon range selected, until module is configured. Gently push the female flexbus connector C into the adjacent terminal base or adapter female connector to 194-ie8 the flexbus connections. Channel 6 analog data sign bit.

Rockwell Automation

Rockwell is one of the world’s leading technology companies. Block transfer programming moves input from the module’s memory to a designated area in the processor data table, and output data words from a designated area in the processor data table to the module’s memory. Marketing Communications, Allen Bradley Co. The configuration BTW sets the bits which enable the programmable features of the module, such as scaling, alarms, ranges, etc.


Chapter Summary In this chapter, you learned how to program your programmable controller. The Input data from Slot 0 is first after the status word, followed by Input data from Slot 2, and so on up to slot 7.

Configure select bits C for individual channels – Bit 08 corresponds to input channel 0, bit 09 corresponds to input channel 1, and so on. Our value-added services include: You must know and understand how DeviceNet Manager works in order to add a device to the network. The following chart manuak each chapter with its corresponding title and a brief overview of the topics covered in that chapter.

Rockwell Automation 1794-IE4XOE2,1794-IE8,1794-OE4,D17946.5.2 FLEX I/O ANALOG MODULE User Manual

Analog modules have 15 words assigned to them. If interlocks are removed, the program may not work properly. Other Comments Use back for more comments. Bits Bits 15 17 Bits Bits 15 17 Definition Channel 0 Safe State analog value – 12 bit left justified two’s complement number; unused lower bits are zero; 4 20mA uses all 16 bits.

Scripting must be enabled to use this site.

Repeat the above steps to install the next module in its terminal base unit. All modules must be analog modules for this configuration. Make sure that the pins on the bottom of the module are straight so they will align properly with the connector in the terminal base unit.


When the multiplex control bits M are cleared simultaneously by a communication error, or by the userthe analog outputs will automatically switch to the values set in the safe state analog words.

This is the sequential operation of both read and write block transfer instructions. Multiplex control bits M for individual channels.

Individual channels revert to 4—20mA with bit selections of all zeroes. Mapping Data for the Analog Modules.

In addition, the data returned from the analog-to-digital converter in the module is bit resolute. Power Requirements, page Installing the Module, page ! This bit is set 1 when 17794-ie8 error is detected in slot position 6.

Data Format The data returned from the analog-to-digital converter in the module is bit resolute. The module is seated when the latching mechanism 7 is locked into the module.

IE8 & OE4 User Manual_百度文库

Thereafter, the program continuously performs read block transfers to configure the module. Press the adapter down flush with the panel until the locking lever locks. The two’s complement of 0 is not found, since no first “1” is ever encountered in the number.